| CATERPILLAR 227-6094 345B II Slewing bearing | Fillet Radius ra:2.50 mm; d:85.000 mm; B:41.00 mm; Sealed Speed Rating n3:2400 rpm; D:180.0000 mm; Basic Static Radial Load Rating Co:96500 N; Grease Speed Rating n1:3600 rpm; Accessories:Shield & Seal; Grease Speed Rating Open/Shielded n1:3600 rpm; Oil Speed Rating Open/Shielded n2:4300 rpm; |
| HITACHI 9188497 ZX110 Slewing bearing | Cap bolt recommended tightening torque:298.3 N·m; Initial grease fill:232.47 g; Pa:20.2 kN; Housing:SSAFS 026 KA; ba:51.594 mm; RG:3/8 NPT; R2:31.75 mm; Mass pillow block:52.2 kg; End plug (suffix Y):EPR 15; P150°:48 kN; |
| HITACHI 9260971 ZX200-3 Slewing bearing | B:28 mm; F:70 mm; Mass inner ring:0.21 kg; r, r1,2 min.:1.1 mm; d:60 mm; |
| KOBELCO PY40F00001F1 40SR-2 Slewing bearing | B1:42 mm; d3:70 mm; s1 max.:7.1 mm; da max.:61.9 mm; r1,2 min.:1.1 mm; Fatigue load limit Pu:11.8 kN; ra max.:1 mm; Mass bearing + sleeve:0.85 kg; D1 ≈:79.4 mm; Misalignment factor k1:0.097; |
| KOBELCO 24100N7529F1 SK115DZ IV Slewing bearing | rb max.:0.6 mm; Da max.:37 mm; Fatigue load limit Pu:1.4 kN; r3,4 min.:0.6 mm; Attainable speed:7200 r/min; Basic static load rating C0:37.5 kN; b:4.2 mm; Basic dynamic load rating C:21.2 kN; ra max.:0.3 mm; da min.:23 mm; |
| KOBELCO 2425U232F1 SK60 III Slewing bearing | U:13 mm; Designation associated SD design radial shaft seal with a low cross-sectional height:SD 18x24x3; Mass needle roller and cage assembly:0.013 kg; Limiting speed:24000 r/min; Fw:18 mm; Fatigue load limit Pu:1.86 kN; Basic dynamic load rating C:12.5 kN; Designation associated G design radial shaft seal with a low cross-sectional height:G 18x24x3; Reference speed:20000 r/min; Basic static load rating C0:15.3 kN; |
| JOHN DEERE 9245728 270D LC Slewing bearing | Specific static load factor K0:45 N/mm²; Specific dynamic load factor K:25 N/mm²; Coefficient of friction µ max.:0.15; a:6 mm; Tolerance housing:H7; h:202.5 mm; Mass bushing:6.97 kg; Permissible sliding velocity v min.:0 m/s; d:200 mm; Permissible sliding velocity v max.:0.5 m/s; |
| JOHN DEERE AT190779 330C LC Slewing bearing | rs (min):2.1 mm; with cylindrical bore:1 700 min-1; B:56 mm; d:150 mm; Dynamic (Cr):4.5 mm; Oil:88.970 kN; Grease:881 kN; D:225 mm; with tapered bore:2 200 min-1; Static (Cor):8.3 mm; |
| CASE KTB0847 CX460 Slewing bearing | d:90.000 mm; D:190.0000 mm; Oil Speed Rating n2:3200 rpm; Basic Dynamic Radial Load Rating C:255000 N; Fillet Radius rb:1.00 mm; Fillet Radius ra:2.50 mm; B:86.00 mm; Basic Static Radial Load Rating Co:270000 N; Grease Speed Rating n1:2200 rpm; |
| JOHN DEERE AT190770 230C LC Slewing bearing | Oil Speed Rating n2:2000 rpm; Basic Static Radial Load Rating Co:510000 N; D:360.0000 mm; d:240.000 mm; Fillet Radius ra:2.50 mm; Grease Speed Rating n1:1700 rpm; Fillet Radius rb:1.00 mm; Basic Dynamic Radial Load Rating C:351000 N; B:56.00 mm; |
| CASE 150997A1 9020 Slewing bearing | Permissible sliding velocity v max.:2.5 m/s; Specific static load factor K0:250 N/mm²; Coefficient of friction µ min.:0.02; Coefficient of friction µ max.:0.2; Specific dynamic load factor K:120 N/mm²; Permissible sliding velocity v min.:0 m/s; B:100 mm; L:500 mm; H:3.06 mm; Mass strip:1.02 kg; |
| JOHN DEERE PG200154 210G LC Slewing bearing | Fillet Radius rb:1.00 mm; D:340.0000 mm; B:136.00 mm; Basic Dynamic Radial Load Rating C:553000 N; Basic Static Radial Load Rating Co:850000 N; Grease Speed Rating n1:1200 rpm; Oil Speed Rating n2:1600 rpm; Fillet Radius ra:3.00 mm; d:160.000 mm; |
| JOHN DEERE 9169646 160C LC Slewing bearing | Calculation factor f1:1; Mass bearing:1.2 kg; r1,2 min.:1.5 mm; Reference grease quantity Gref:14 cm³; Db max.:134.4 mm; Preload class B GB:580 N; Calculation factor f0:9.6; r3,4 min.:1 mm; Attainable speed for grease lubrication:13300 r/min; Da max.:133 mm; |
| HITACHI 9245698 ZX350-3 Slewing bearing | J min.:131.762 mm; Mass bearing unit:3.65 kg; A:58.737 mm; da:44.45 mm; Basic dynamic load rating C:102 kN; H:109.537 mm; H1:53.975 mm; Limiting speed:4500 r/min; H2:33.337 mm; S:0.794 mm; |